HW5 Large Lid Handle(sku: 1029)
Lid and side handles for large kilns, 10 sides and more.
Help us to make sure we send you the right part and enter the model number and serial number of the kiln for which you need this part:
TF5 Half Amp Fuse(sku: 6726)
TF5 Half Amp Fuse, AGC, 250V AC. This fuse protects the digital controller. The fuse is mounted in the kiln's control panel (usually on the side of the kiln).
PY80-4 Thermocouple (PY50)(sku: 6750-14)
Thermocouple (temperature sensor), K-type, 1/4” diameter, exposed tip 14-gauge complete with ceramic block and lead wires for 2 1/2” - 3” wall kilns. (Order the PY81-4 if you do not need to replace the ceramic block or lead wires.) Our beaded thermocouple with polished tip is rugged and reliable. The thermocouple is made in the U.S. with American-made components to exacting standards. The “special limit” thermocouple wire is certified to be close tolerance.
CONTROL BOARD, SENTRY II, 1700 DEGREES F (MAX TEMP)
CORDSET, 50 AMP, 240 VOLT, NEMA 6-50, 6 FOOT
ELEMENT, GL24ADTSD, 240V, DOOR, 9 OHM, 3 PER KILN
The element comes pre-stretched for a precise fit. Element connectors are included with each new element.
ELEMENT, GL24ADTSD, 240V, SIDE, 23 OHM, 3 PER KILN
MS1 Porcelain Insulators(sku: MS1)
MS1 Porcelain Insulators, 1 1/8" long (28.57 mm). 4 per package. The insulators prevent the element from touching the kiln case.
MS6 Element Connectors(sku: MS6)
MS6 Element Connectors, brass, 2 per package. Use new connectors when replacing an element. (Note: Paragon replacement elements come with new connectors.)
PILOT LIGHT with push-on terminals.
TF9 Fuse Holder for Switch Box of Digital Kilns(sku: TF9)
Fuse Holder for the kiln's AGC half amp fuse. The fuse holder is built into the kiln control panel (usually located on the side of the kiln).
Muffle Roof for GL-24 Series Kilns, Front & Middle(sku: 30870-1)
MUFFLE GL24 32 OHM, TOP FRONT, MIDDLE SECTION This piece works as the middle section and front section of the embedded fiber top roof. The other one is the rear section. The price is per each section. To replace the entire lid you need a front, middle and rear section (three sections total).
Muffle Roof for GL-24 Series Kilns, Rear(sku: 30870-2)
MUFFLE GL24 32 OHM TOP REAR SECTION This piece is the top rear section of the embedded fiber roof. The price is per each section. To replace the entire lid you will need this section plus a front and a middle section (three sections total).
SW6 Infinite Control Switch, 240V(sku: 4151)
Infinite control switch, 240 volt. The switch cycles the elements on and off. The higher the switch setting, the longer the elements stay on with each cycle. on High, the elements stay on continuously. (Note: If you are replacing a Duncan KM300 switch with the SW6, the switch must be installed upside-down. --Thank you)
PY81-4 Thermocouple, K-Type, 2.5-3 inch Wall Kilns(sku: 60179-4)
Thermocouple (temperature sensor), K-type, 1/4” diameter, exposed tip 14-gauge for 2 1/2” - 3” wall kilns (less ceramic block and wires). Our beaded thermocouple with polished tip is rugged and reliable. The thermocouple is made in the U.S. with American-made components to exacting standards. The “special limit” thermocouple wire is certified to be close tolerance.
TF26 Mercury Relay, 30 amp(sku: 6022-1)
Mercury relay, 30 amps with 200-240 volt coil.
TF71 Sentry Control Cable(sku: 6060-1)
TF71 12-key Sentry Control Cable. You will need this part when upgrading from the earlier DTC-series controllers to the Sentry 12-key or Sentinel Smart Touch.
TF3 Relay 30 Amp(sku: 6355)
Relay, 30 amp, 12 volt coil. The relay sends power to the elements of digital kilns.
Paragon Industries, L.P.,
2011 South Town East Blvd.
Mesquite, Texas 75149-1122
Copyright © 2020,Paragon Industries, L.P.
“Custom and standard Kilns and Industrial Furnaces for ceramics, pottery, heat treating, enameling,dentistry, laboratory, and glass fusing.Better Designed Kilns from Paragon Industries!"