TF5 Half Amp Fuse(sku: 6726)
TF5 Half Amp Fuse, AGC, 250V AC. This fuse protects the digital controller. The fuse is mounted in the kiln's control panel (usually on the side of the kiln).
Help us to make sure we send you the right part and enter the model number and serial number of the kiln for which you need this part:
CONTROL BOARD, SENTRY II, 1700 DEGREES F (MAX TEMP)
Sentinel Smart Touch Controller, replacement part(sku: 6844-71)
The Sentinel Smart Touch controller can replace the standard Sentry 2.0 12-key controller. The price shown here is for the Sentinel controller purchased for an existing kiln.
The Sentinel Smart Touch is made by Bartlett Instruments of Fort Madison, Iowa.
Ramp-Hold programs can have a customized program title, which is entered through the touch screen. Store 12 custom programs with up to 32 segments per program. The Sentinel includes Novice Mode, which adds questions to guide you during programming.
The controller can be updated through WiFi. View the progress of a firing in graph mode. The firing schedule can be edited during firing with Skip Step, Add Segments, Add Temperature, and Add Time. The Sentinel can turn a kiln vent or gas injection flow meter on or off for each segment of a program.
CORDSET, 15 AMP, 120 VOLT, NEMA 5-15, 6 FOOT
MS1 Porcelain Insulators(sku: MS1)
MS1 Porcelain Insulators, 1 1/8" long (28.57 mm). 4 per package. The insulators prevent the element from touching the kiln case.
THERMOCOUPLE with beads for the SC and BlueBird kilns.
MS6 Element Connectors(sku: MS6)
MS6 Element Connectors, brass, 2 per package. Use new connectors when replacing an element. (Note: Paragon replacement elements come with new connectors.)
PY80-4 Thermocouple (PY50)(sku: 6750-14)
Thermocouple (temperature sensor), K-type, 1/4” diameter, exposed tip 14-gauge complete with ceramic block and lead wires for 2 1/2” - 3” wall kilns. (Order the PY81-4 if you do not need to replace the ceramic block or lead wires.) Our beaded thermocouple with polished tip is rugged and reliable. The thermocouple is made in the U.S. with American-made components to exacting standards. The “special limit” thermocouple wire is certified to be close tolerance.
Muffle, Ceramic Fiber, for J-11 and Xpress J-11(sku: 30873-1)
Ceramic fiber firing chamber (muffle) for the J11 and Xpress-J11. The firing chamber includes embedded elements. Before ordering a new muffle, check the element connectors. If one has burned off, you can usually repair the muffle without replacing it. Merely replace the element connector.
Door, Ceramic Fiber, for J-11 and Xpress-J-11(sku: 30873-2)
This is the ceramic fiber insert for the J-11 and Xpress-J-11 door.
PY81-4 Thermocouple, K-Type, 2.5-3 inch Wall Kilns(sku: 60179-4)
Thermocouple (temperature sensor), K-type, 1/4” diameter, exposed tip 14-gauge for 2 1/2” - 3” wall kilns (less ceramic block and wires). Our beaded thermocouple with polished tip is rugged and reliable. The thermocouple is made in the U.S. with American-made components to exacting standards. The “special limit” thermocouple wire is certified to be close tolerance.
TF9 Fuse Holder for Switch Box of Digital Kilns(sku: 6018)
Fuse Holder for the kiln's AGC half amp fuse. The fuse holder is built into the kiln control panel (usually located on the side of the kiln).
TF71 Sentry Control Cable(sku: 6060-1)
TF71 12-key Sentry Control Cable. You will need this part when upgrading from the earlier DTC-series controllers to the Sentry 12-key or Sentinel Smart Touch.
TF3 Relay 30 Amp(sku: 6355)
Relay, 30 amp, 12 volt coil. The relay sends power to the elements of digital kilns.
Paragon Industries, L.P.,
2011 South Town East Blvd.
Mesquite, Texas 75149-1122
Copyright © 2019,Paragon Industries, L.P.
“Custom and standard Kilns and Industrial Furnaces for ceramics, pottery, heat treating, enameling,dentistry, laboratory, and glass fusing.Better Designed Kilns from Paragon Industries!"