KN7 Knob with Pointer(sku: 4204)
KN7 Knob with Pointer (for S and SnF series Paragon kilns)
Help us to make sure we send you the right part and enter the model number and serial number of the kiln for which you need this part:
PL2 Peephole Plug Cone Shaped(sku: 2000)
PL2 Peephole Plug Cone Shaped
MS6 Element Connectors(sku: 4003)
MS6 Element Connectors (2 per package). Use new connectors when replacing an element. (Note: Paragon replacement elements come with new connectors.)
HW7 Prop-R-Vent(sku: HW7)
HW7 fall away Prop-R-Vent kit for top-loading kilns.
Kiln Sitter Cone Supports, KS-2(sku: KS-2)
Insert the cone supports into the slots in the Kiln Sitter porcelain tube. Package of 2.
Release Claw for Kiln Sitter(sku: RELEASECLAW)
Release Claw for the Dawson Kiln Sitter and the Orton Auto-Cone. Fits all sensing rods. Instructions included.
Timer Motor(sku: TIMERMOTOR)
Motor for the Limit Timer on the Dawson Kiln Sitter and the Orton Auto-Cone. 208 - 240 volt, 60 hertz.
Rolling Stand Replacement Part, 24x24x12 inches(sku: SKU STD242412-BA)
The replacement stand for your Paragon 10-sided top-loading ceramic kiln has locking casters, a mounting bracket for the Orton Kiln Vent, and a greenware drying rack. (Load greenware on the lower shelf. Heat from the kiln will dry the ware for the next firing.) Roll the kiln out of the way when not using it. Ships unassembled. Assembly instructions included. This deluxe stand replaces the discontinued standard kiln stand. 24” square x 12” high. Ships in a 27” x 27” x 8” carton.
LIMIT TIMER KILN SITTER
PILOT LIGHT with push-on terminals.
KS7 Kiln Sitter Tube Assembly(sku: 4041)
KS7 Dawson Kiln Sitter or Orton Auto-Cone Tube Assembly for the Paragon S and SnF series kilns. The replacement tube assembly may not look exactly the same as the original, because we have changed manufacturers. Do not be concerned; the tube assembly will still fit.
STEPLESS CONTROL SWITCH 240 VOLTS
(Note: If you are replacing a Duncan KM300 switch with the SW-6, the switch must be installed upside-down. --Thank you)
MS1 Porcelain Insulators(sku: 2013)
MS1 Porcelain Insulators, 1 1/8" long (4 per package). The insulators prevent the element from touching the kiln case.
BOTTOM PAN FOR 10 SIDED KILNS
RELAY 25 AMP, 200-240 COIL
PLASTIC FEET FOR KILN STAND
STRAIGHT, 2 GROOVE BRICK, 10 SIDE, 2.5" BRICK When ordering bricks, always specify the Paragon kiln model number, which is listed on the kiln's safety data plate.
TERMINAL 2 GROOVE BRICK, 10 SIDE, 2.5" BRICK When ordering bricks, always specify the Paragon kiln model number, which is listed on the kiln's safety data plate.
BRICK BOTTOM FOR 99, 24, 24-3
LID FOR A23B3, A24B3, S99. The lid comes with a band, but it does not include hardware such as the hinge and handle.
CORDSET, 50 AMP, 240 VOLT, NEMA 6-50, 6 FOOT
ELEMENT, S99 208V TBM 26 OHM, 6 PER KILN
The element comes pre-stretched and bent at the wallbrick corners for a precise fit. Element connectors are included with each new element.
Paragon Industries, L.P.,
2011 South Town East Blvd.
Mesquite, Texas 75149-1122
Copyright © 2018,Paragon Industries, L.P.
“Custom and standard Kilns and Industrial Furnaces for ceramics, pottery, heat treating, enameling,dentistry, laboratory, and glass fusing.Better Designed Kilns from Paragon Industries!"