TF5 Half Amp Fuse(sku: 6726)
TF5 Half Amp Fuse, AGC, 250V AC. This fuse protects the digital controller. The fuse is mounted in the kiln's control panel (usually on the side of the kiln).
Help us to make sure we send you the right part and enter the model number and serial number of the kiln for which you need this part:
HW7 Prop-R-Vent(sku: HW7)
HW7 fall away Prop-R-Vent kit for top-loading kilns.
PL2 Peephole Plug Cone Shaped(sku: 2000)
PL2 Peephole plug, cone shaped. Keep a spare on hand in case you drop one. The plug is essential for kilns equipped with a downdraft vent.
PY81-4 Thermocouple, K-Type, 2.5-3 inch Wall Kilns(sku: 60179-4)
Thermocouple (temperature sensor), K-type, 1/4” diameter, exposed tip 14-gauge for 2 1/2” - 3” wall kilns (less ceramic block and wires). Our beaded thermocouple with polished tip is rugged and reliable. The thermocouple is made in the U.S. with American-made components to exacting standards. The “special limit” thermocouple wire is certified to be close tolerance.
TF3 Relay 30 Amp(sku: 6355)
Relay, 30 amp, 12 volt coil. The relay sends power to the elements of digital kilns.
MS1 Porcelain Insulators(sku: MS1)
MS1 Porcelain Insulators, 1 1/8" long (28.57 mm). 4 per package. The insulators prevent the element from touching the kiln case.
MS6 Element Connectors(sku: MS6)
MS6 Element Connectors, brass, 2 per package. Use new connectors when replacing an element. (Note: Paragon replacement elements come with new connectors.)
PY80-4 Thermocouple (PY50)(sku: 6750-14)
Thermocouple (temperature sensor), K-type, 1/4” diameter, exposed tip 14-gauge complete with ceramic block and lead wires for 2 1/2” - 3” wall kilns. (Order the PY81-4 if you do not need to replace the ceramic block or lead wires.) Our beaded thermocouple with polished tip is rugged and reliable. The thermocouple is made in the U.S. with American-made components to exacting standards. The “special limit” thermocouple wire is certified to be close tolerance.
TF9 Fuse Holder for Switch Box of Digital Kilns(sku: TF9)
Fuse Holder for the kiln's AGC half amp fuse. The fuse holder is built into the kiln control panel (usually located on the side of the kiln).
Rolling Stand Replacement Part, 18x18x12 inches(sku: SKU STD181812-BA)
The replacement stand for your Paragon 7- and 8-sided top-loading ceramic kiln has locking casters, a mounting bracket for the Orton Kiln Vent, and a greenware drying rack. (Take advantage of the heat that radiates from the kiln. Load greenware onto the lower shelf. Heat from the kiln will dry the ware for the next firing.) Roll the kiln out of the way when not using it. Ships unassembled. Assembly instructions included. This deluxe stand replaces the discontinued standard kiln stand. 18” square x 12” high. Ships in a 20” x 25” x 7” carton.
SSP CONTROLLER SENTRY XPRESS CONE 04/2000F
SSP CONTROLLER SENTRY XPRESS CONE 10/2400F
PLASTIC FEET FOR KILN STAND
BRC STRAIGHT 2 GROOVE BRICK, 6 SIDE, 2.5" BRICK When ordering bricks, always specify the Paragon kiln model number, which is listed on the kiln's safety data plate.
TERMINAL 2 GROOVE BRICK, 6 SIDE, 3" BRICK When ordering firebricks, always specify the Paragon kiln model number, which is listed on the kiln's safety data plate.
CORDSET, 20 AMP, 120 VOLT, NEMA 5-20, 6 FOOT
ELEMENT, 1193 S/XPRESS 120V, 13.1 OHM, 2 PER KILN
The element comes pre-stretched and bent at the wallbrick corners for a precise fit. Element connectors are included with each new element.
HW4 Small Lid Handle(sku: 1001)
Lid handle for small kilns, 8 sides or less.
TF72 Sentry Xpress Control Cable(sku: 6060-2)
TF72 Sentry Xpress Control Cable
Paragon Industries, L.P.,
2011 South Town East Blvd.
Mesquite, Texas 75149-1122
Copyright © 2020,Paragon Industries, L.P.
“Custom and standard Kilns and Industrial Furnaces for ceramics, pottery, heat treating, enameling,dentistry, laboratory, and glass fusing.Better Designed Kilns from Paragon Industries!"