Release Claw for Kiln Sitter(sku: RELEASECLAW)
Release Claw for the Dawson Kiln Sitter and the Orton Auto-Cone. Fits all sensing rods. Instructions included.
Help us to make sure we send you the right part and enter the model number and serial number of the kiln for which you need this part:
Timer Motor(sku: TIMERMOTOR)
Motor for the Limit Timer on the Dawson Kiln Sitter and the Orton Auto-Cone. 208 - 240 volt, 60 hertz.
WR20 Wires for SW4(sku: WR20)
WR20 #14 switch-to-element wires for SW4 (Set of 1 WR14, 2 WR4)
KS1 Kiln Sitter Tube Assembly(sku: 4039)
KS1 Dawson Kiln Sitter Tube Assembly for the Paragon A series, 2 1/2" thick wall kilns. The replacement tube assembly may not look exactly the same as the original, because we have changed manufacturers. Do not be concerned; the tube assembly will still fit.
HW7 Prop-R-Vent(sku: HW7)
HW7 fall away Prop-R-Vent kit for top-loading kilns.
Kiln Sitter Cone Supports, KS-2(sku: KS-2)
Insert the cone supports into the slots in the Kiln Sitter porcelain tube. Package of 2.
PILOT LIGHT with push-on terminals.
HW4 Small Lid Handle(sku: 1001)
Lid handle for small kilns, 8 sides or less.
PLASTIC FEET FOR KILN STAND
Firebrick, 4" straight grooved wall brick, 3 grooves, 2.5" thick, for a 6-sided kiln. When ordering firebricks, always specify the Paragon kiln model number, which is listed on the kiln's safety data plate.
Firebrick, 2" plain, no grooves, 2.5" thick, for a six-sided kiln. When ordering firebricks, always specify the Paragon kiln model number, which is listed on the kiln's safety data plate.
CORDSET, 15 AMP, 120 VOLT, NEMA 5-15, 6 FOOT
ELEMENT A116B #4064 7.5 OHM SL=142 PT=4 F=6, 1 PER KILN
The element comes pre-stretched and bent at the wallbrick corners for a precise fit. Element connectors are included with each new element.
BP6 Full Formed Steel Base, 6 Sided Kilns(sku: 3147)
The full-formed steel base for 6-sided kilns. The base is made of long-lasting galvanized steel. It protects the firebrick kiln bottom. Install the steel base by removing the old one and sliding the tabs of the new one up behind the stainless steel case. Then fasten with screws.
KN3 Knob for 4 way rotary switch(sku: 4037)
Knob for 4 way rotary switch (Off, Low, Med, High). Black plastic with white letters.
MS1 Porcelain Insulators(sku: MS1)
MS1 Porcelain Insulators, 1 1/8" long (28.57 mm). 4 per package. The insulators prevent the element from touching the kiln case.
MS6 Element Connectors(sku: MS6)
MS6 Element Connectors, brass, 2 per package. Use new connectors when replacing an element. (Note: Paragon replacement elements come with new connectors.)
Rolling Stand Replacement Part, 18x18x12 inches(sku: SKU STD181812-BA)
The replacement stand for your Paragon 7- and 8-sided top-loading ceramic kiln has locking casters, a mounting bracket for the Orton Kiln Vent, and a greenware drying rack. (Take advantage of the heat that radiates from the kiln. Load greenware onto the lower shelf. Heat from the kiln will dry the ware for the next firing.) Roll the kiln out of the way when not using it. Ships unassembled. Assembly instructions included. This deluxe stand replaces the discontinued standard kiln stand. 18” square x 12” high. Ships in a 20” x 25” x 7” carton.
Firebrick, peephole, 3 grooves, 2.5" thick, for a 6-sided kiln. When ordering firebricks, always specify the Paragon kiln model number, which is listed on the kiln's safety data plate.
Firebrick, terminal, 3 grooves, 2.5" thick, for a 6-sided kiln. When ordering firebricks, always specify the Paragon kiln model number, which is listed on the kiln's safety data plate.
Paragon Industries, L.P.,
2011 South Town East Blvd.
Mesquite, Texas 75149-1122
Copyright © 2020,Paragon Industries, L.P.
“Custom and standard Kilns and Industrial Furnaces for ceramics, pottery, heat treating, enameling,dentistry, laboratory, and glass fusing.Better Designed Kilns from Paragon Industries!"