TF5 Half Amp Fuse(sku: 6726)
TF5 Half Amp Fuse, AGC, 250V AC. This fuse protects the digital controller. The fuse is mounted in the kiln's control panel (usually on the side of the kiln).
Help us to make sure we send you the right part and enter the model number and serial number of the kiln for which you need this part:
HW5 Large Lid Handle(sku: 1029)
Lid and side handles for large kilns, 10 sides and more.
TF71 Sentry Control Cable(sku: 6060-1)
TF71 12-key Sentry Control Cable. You will need this part when upgrading from the earlier DTC-series controllers to the Sentry 12-key or Sentinel Smart Touch.
CONTROL BOARD, SENTRY II, 1700 DEGREES F (MAX TEMP)
PLASTIC FEET FOR KILN STAND
PLAIN, NO GROOVE BRICK, 10 SIDE, 2.5" BRICK When ordering firebricks, always specify the Paragon kiln model number, which is listed on the kiln's safety data plate.
BRICK BOTTOM FOR 99, 24, 24-3
LID FOR GF10B WITH ELEMENT. The lid comes with a band, but it does not include hardware such as the hinge and handle.
CORDSET, 50 AMP, 240 VOLT, NEMA 6-50, 6 FOOT
ELEMENT GF10BD, 240 VOLTS, 19 OHMS, 3 PER KILN
The element comes pre-stretched for a precise fit. Element connectors are included with each new element.
Fiber Lid Replacement Part(sku: Fiber Lid Replacement Part)
You can replace your firebrick lid with a ceramic fiber one. (Please specify the kiln model when ordering. The photo shows a Fusion-8 lid but represents all Fusion models.) Serious glass artists have long requested the fiber lid for their firebrick kilns. The ceramic fiber lid includes a deluxe brushed stainless steel outer lid cover.
Rolling Stand Replacement Part, 24x24x18 inches(sku: SKU STD242418-BA)
The replacement stand for your Paragon 10-sided top-loading glass kiln has locking casters, and a mounting bracket for the Orton Kiln Vent. Move the kiln out of the way when not in use. The glass kiln deluxe stand is 18” high, which raises the kiln to a comfortable height. Assembly required; instructions included. This deluxe stand replaces the discontinued standard kiln stand. 24” square x 18” high. Ships in a 27” x 27” x 8” carton.
PL2 Peephole Plug Cone Shaped(sku: 2000)
PL2 Peephole plug, cone shaped. Keep a spare on hand in case you drop one. The plug is essential for kilns equipped with a downdraft vent.
BP10 Full Formed Steel Base, 10 Sided Kilns(sku: 3090)
The full-formed steel base for 10-sided kilns. The base is made of long-lasting galvanized steel. It protects the firebrick kiln bottom. Install the steel base by removing the old one and sliding the tabs of the new one up behind the stainless steel case. Then fasten with screws.
PY81-4 Thermocouple, K-Type, 2.5-3 inch Wall Kilns(sku: 60179-4)
Thermocouple (temperature sensor), K-type, 1/4” diameter, exposed tip 14-gauge for 2 1/2” - 3” wall kilns (less ceramic block and wires). Our beaded thermocouple with polished tip is rugged and reliable. The thermocouple is made in the U.S. with American-made components to exacting standards. The “special limit” thermocouple wire is certified to be close tolerance.
TF9 Fuse Holder for Switch Box of Digital Kilns(sku: 6018)
Fuse Holder for the kiln's AGC half amp fuse. The fuse holder is built into the kiln control panel (usually located on the side of the kiln).
TF3 Relay 30 Amp(sku: 6355)
Relay, 30 amp, 12 volt coil. The relay sends power to the elements of digital kilns.
MS1 Porcelain Insulators(sku: MS1)
MS1 Porcelain Insulators, 1 1/8" long (28.57 mm). 4 per package. The insulators prevent the element from touching the kiln case.
MS6 Element Connectors(sku: MS6)
MS6 Element Connectors, brass, 2 per package. Use new connectors when replacing an element. (Note: Paragon replacement elements come with new connectors.)
PY80-4 Thermocouple (PY50)(sku: 6750-14)
Thermocouple (temperature sensor), K-type, 1/4” diameter, exposed tip 14-gauge complete with ceramic block and lead wires for 2 1/2” - 3” wall kilns. (Order the PY81-4 if you do not need to replace the ceramic block or lead wires.) Our beaded thermocouple with polished tip is rugged and reliable. The thermocouple is made in the U.S. with American-made components to exacting standards. The “special limit” thermocouple wire is certified to be close tolerance.
Paragon Industries, L.P.,
2011 South Town East Blvd.
Mesquite, Texas 75149-1122
Copyright © 2019,Paragon Industries, L.P.
“Custom and standard Kilns and Industrial Furnaces for ceramics, pottery, heat treating, enameling,dentistry, laboratory, and glass fusing.Better Designed Kilns from Paragon Industries!"