HW4 Small Lid Handle(sku: 1001)
Lid handle for small kilns, 8 sides or less.
Help us to make sure we send you the right part and enter the model number and serial number of the kiln for which you need this part:
PLASTIC FEET FOR KILN STAND
PLAIN, NO GROOVE BRICK, 8 SIDE, 2.5" BRICK When ordering firebricks, always specify the Paragon kiln model number, which is listed on the kiln's safety data plate.
BRICK BOTTOM FOR 82,81,88
LID FOR GF85B WITH ELEMENT. The lid comes with a band, but it does not include hardware such as the hinge and handle.
CORDSET, 20 AMP, 240 VOLT, NEMA 6-20, 6 FOOT
ELEMENT GF85B, 240 VOLTS, 16 OHMS, 1 PER KILN
The element comes pre-stretched for a precise fit. Element connectors are included with each new element.
Fiber Lid Replacement Part(sku: Fiber Lid Replacement Part)
You can replace your firebrick lid with a ceramic fiber one. (Please specify the kiln model when ordering. The photo shows a Fusion-8 lid but represents all Fusion models.) Serious glass artists have long requested the fiber lid for their firebrick kilns. The ceramic fiber lid includes a deluxe brushed stainless steel outer lid cover.
PILOT LIGHT with push-on terminals.
PL2 Peephole Plug Cone Shaped(sku: 2000)
PL2 Peephole plug, cone shaped. Keep a spare on hand in case you drop one. The plug is essential for kilns equipped with a downdraft vent.
BP8 Full Formed Steel Base, 8 Sided Kilns(sku: 3005)
The full-formed steel base for 8-sided kilns. The base is made of long-lasting galvanized steel. It protects the firebrick kiln bottom. Install the steel base by removing the old one and sliding the tabs of the new one up behind the stainless steel case. Then fasten with screws.
SW6 Infinite Control Switch, 240V(sku: 4151)
Infinite control switch, 240 volt. The switch cycles the elements on and off. The higher the switch setting, the longer the elements stay on with each cycle. on High, the elements stay on continuously. (Note: If you are replacing a Duncan KM300 switch with the SW6, the switch must be installed upside-down. --Thank you)
KN4 Knob for Infinite Control Switch(sku: 4133)
KN4 Knob for Infinite Control Switch, with printed numbers. Black plastic and white numbers.
Rolling Stand Replacement Part, 18x18x18 inches(sku: SKU STD181818-BA)
The replacement stand for your Paragon 7- and 8-sided top-loading kiln has locking casters and a mounting bracket for the Orton Kiln Vent. Move the kiln out of the way when not in use. The deluxe stand is a comfortable 18” high. Assembly required; instructions included. This deluxe stand replaces the discontinued standard kiln stand. 18” square x 18” high. Ships in a 25” x 19” x 8” carton.
MS1 Porcelain Insulators(sku: MS1)
MS1 Porcelain Insulators, 1 1/8" long (28.57 mm). 4 per package. The insulators prevent the element from touching the kiln case.
MS6 Element Connectors(sku: MS6)
MS6 Element Connectors, brass, 2 per package. Use new connectors when replacing an element. (Note: Paragon replacement elements come with new connectors.)
Paragon Industries, L.P.,
2011 South Town East Blvd.
Mesquite, Texas 75149-1122
Copyright © 2019,Paragon Industries, L.P.
“Custom and standard Kilns and Industrial Furnaces for ceramics, pottery, heat treating, enameling,dentistry, laboratory, and glass fusing.Better Designed Kilns from Paragon Industries!"