HW7 fall away Prop-R-Vent kit for top-loading kilns.
Help us to make sure we send you the right part and enter the model number and serial number of the kiln for which you need this part:
Insert the cone supports into the slots in the Kiln Sitter porcelain tube. Package of 2.
KN3 Knob for 4 way rotary switch (Off, Low, Med, High)
PL2 Peephole Plug Cone Shaped
Release Claw for the Dawson Kiln Sitter and the Orton Auto-Cone. Fits all sensing rods. Instructions included.
MS6 Element Connectors (2 per package). Use new connectors when replacing an element. (Note: Paragon replacement elements come with new connectors.)
MS7 Pilot light with eyelet terminals. This part replaces the pilot light on kilns equipped with the early 4-way rotary switch with ring terminals. Order the MS8 if your switch has push-on terminals.
Motor for the Limit Timer on the Dawson Kiln Sitter and the Orton Auto-Cone. 208 - 240 volt, 60 hertz.
WR20 #14 switch-to-element wires for SW4 (Set of 1 WR14, 2 WR4)
PILOT LIGHT with push-on terminals.
PLASTIC FEET FOR KILN STAND
Kiln stand for 6-, 7-, and 8-sided kilns. 9" tall. Assembly required. (This stand is furnished with a new kiln.)
SWC SWITCH 26AMP A21 4WAY ROTARY
MS1 Porcelain Insulators, 1 1/8" long (4 per package). The insulators prevent the element from touching the kiln case.
BOTTOM PAN FOR 8 SIDED KILNS
BRC STRAIGHT 3 GROOVE, 8 SIDE, 2.5" BRICK When ordering bricks, always specify the Paragon kiln model number, which is listed on the kiln's safety data plate.
BRC TERMINAL 3 GROOVE BRICK, 8 SIDE, 2.5" BRICK When ordering firebricks, always specify the Paragon kiln model number, which is listed on the kiln's safety data plate.
BRC PEEPHOLE 3 GROOVE BRICK, 8 SIDE, 2.5" BRICK When ordering firebricks, always specify the Paragon kiln model number, which is listed on the kiln's safety data plate.
The peephole brick comes undrilled. At the factory we drill peepholes with a large, tapered drill bit. You can improvise, however, by drilling the peephole with a 1/4" bit. Use a hacksaw blade or knife to expand the hole. For final shaping, wrap a piece of sandpaper around the peephole plug and rotate inside the new peephole.
The bottom of the peephole should be horizontal, or parallel to the floor; the top of the peephole should be angled downward. If instead the peephole is drilled straight in, the plug may fall out during firing.
BRICK BOTTOM FOR 82,81,88
LID FOR 82B, 88B, 81B. The lid comes with a band, but it does not include hardware such as the hinge and handle.
Cord Set AS 6-4 50A 240V 6 foot cord with 4-prong plug. 14-50P
SIC KS W/LT 240/60 Complete with separate mounting box and tube for 2.5" wall A-series kiln.
ELEMENT A88B #4073 9.25 OHMS SL=165, 4 PER KILN
The element comes pre-stretched and bent at the wallbrick corners for a precise fit. Element connectors are included with each new element.
Lid handle for small kilns, 8 sides or less.
Paragon Industries, L.P.,
2011 South Town East Blvd.
Mesquite, Texas 75149-1122
Copyright © 2018,Paragon Industries, L.P.
“Custom and standard Kilns and Industrial Furnaces for ceramics, pottery, heat treating, enameling,dentistry, laboratory, and glass fusing.Better Designed Kilns from Paragon Industries!"