PMT13 Kiln is a kiln used for Heat Treating,Industrial use. Better Designed Kilns From Paragon.

Kilns and Furnaces for ceramics, pottery, heat treating, enameling, dentistry, laboratory testing and glass fusing. Better Designed Kilns!

SEARCH:

PMT13

Heat Treating Knife Making Industrial

Product Videos

Watch & Listen to P001 The Paragon Kiln Factory Sheetmetal Department (3 min 40 sec)

Watch & Listen to P004 The Paragon Kiln Factory Square Kiln Assembly Line (4 min 30 sec)

Watch & Listen to P005 The Paragon Kiln Factory Firebrick Room (6 min 47 sec)

Watch & Listen to P008 The Paragon Kiln Factory Inspection Station (1 min 50 sec)

Features

Paragon PMT-13 Heat Treating Furnace

Machine shops save time with a furnace at their disposal in their own shop. You will no longer send a die out for heat treating, wait for its return and then send it out again for additional heat treating.

Solid construction

The door swings open with one-handed operation. The PMT-13 furnace is insulated with refractory firebrick. The elements are mounted in dropped, recessed grooves machined into the firebrick. Paragon invented this type of groove in 1952. This groove protects the element for long life and low maintenance. Elements are simple to replace because they’re exposed rather than embedded. You can thread new elements into place following clear instructions in the manual.

The firing chamber is protected by a steel case painted in high temperature blue. A built-in stand lifts the firing chamber safely off your worktable, so no extra stand is needed. The door is mounted with a heavy-duty hinge for smooth opening. A micro-switch shuts off the power to the elements when the door is opened. We use high temperature wire in the switch box for long life. A heat shield, mounted between the switch box and furnace, helps keep the switch box components cool even during extended operation. To further dissipate heat, the switch box is extra large and generously louvered. Each furnace comes with a cord and plug for immediate installation and a one year warranty.

Complete instructions

Your furnace includes a wiring diagram, programming instructions, and heat treating manual. The manual gives you basic heat treating instructions for D2, 440C, ATS 34 and 154 CM. The manual is written in plain English for the beginner.

Optional Gas Injection Flow Meter

During heat treating, scale forms on the surface of the steel. One way to eliminate most scaling is to wrap the steel in stainless steel foil. An easier way is to install the gas injection flow meter on your furnace. It is available as either an add-on kit, or you can order the furnace with the meter installed.

The meter regulates the flow of an inert gas, such as argon, inside the furnace. The gas displaces the oxygen to prevent most scaling.

Specifications

Max. Temperature	2350F 1287C
Amps	17
Phase	1
Watts	3600
Nema	6-20P
Breaker Size	20
Circuit Wire Size	12 gauge
TUV tested to CSA and UL Standard 499	N
CE	N
Control Type	Sentry Digital 12-key Non-Ceramic
Voltage	208
Hertz	60
Disclaimer: The specifications above assume that the kiln will be plugged into a dedicated circuit. Local electric codes supersede our recommendations. The pricing and electrical specifications for the above products reflect their design for use in the United States. The International versions of most models will have variations in electrical specifications and price due to consumer safety requirements or electrical regulations.

Sides	4
Chamber Volume	0.80 CU.FT. 22.65 litres
Chamber Width	13.00 330 mm
Chamber Depth	13.00 330 mm
Chamber Height	8.50 216 mm
The Outer Size of the Kiln and the Shipping Size: Width = Left to Right; Depth = Front to Back; Height = Top to Bottom
Outer Size	34.00W x 25.00D x 23.00H Inches 864W x 635D x 584H mm
Ship Size	38.00W x 29.00D x 27.00H Inches 965W x 737D x 686H mm
Ship Weight	160.00 Lbs. 72.58 Kg.
Ship Method & Notations	This Kiln Ships Via Truck


Part Number	PMT13-1
Price	$2,320.00
Quantity

Options
	Part Number	Description	Quantity	Price
	1332 Gas Inlet Flow Meter	KIT 1/4" GAS INLET AND FLOW METER (MANUAL) During heat treating, scale forms on the surface of the steel. One way to eliminate most scaling is to wrap the steel in stainless steel foil. An easier way is to install the gas injection flow meter on your		$200.00
	Firing Safety Glasses	Wear firing safety glasses whenever looking into the firing chamber of a hot kiln. Filters the infra-red and ultra-violet light. Reduces glare, makes pyrometric cones easier to see.		$19.50
	Knifemakers Heat Treating Kit	Contains 1 pair hot gloves, 1 heat treating fork, 4 knifeholders, and 8 firebrick supports. Hot Gloves For intermittent handling of hot objects up to 400° F. Sold in pairs. Not intended for handling hot blades. Heat Treatin		$64.00